MS Sheet Weight Formula: kg per sq ft, SWG and 8 x 4
How to find the weight of an MS, CRCA, GI or stainless sheet in kg from mm or SWG, with kg per sq ft for 8 x 4 sheets and the zinc on GI sheet counted.
By Redbison Dev · · 9 min read

India edition. Written for Indian fabricators, dealers and buyers: 8 x 4 ft sheets, SWG gauges, kg per sq ft, GI coating in gsm and the Ministry of Steel's quality control orders. US edition
An 8 x 4 ft MS sheet in 18 SWG (1.219 mm) weighs 28.49 kg. The formula behind it is length x width x thickness x density, and for steel it shortens to a rule worth memorising: thickness in mm x 7.85 = kg per square metre, or thickness in mm x 0.729 = kg per sq ft. Multiply by the sheet area and you have the weight a dealer's rate per kg applies to. The places where Indian estimates slip are the gauge ("18 gauge" from an American chart is not 18 SWG), the zinc on GI sheet, and mixing feet with millimetres. This edition works through each with the MS and GI sheet weight calculator, which opens on an 8 x 4 sheet in SWG.
The formula, in the units Indian shops use
Steel is sold by the kilogram but sized in a mix of mm and feet. An "8 x 4" sheet is quoted as 2440 x 1220 mm, which is 2.9768 m² or about 32 sq ft.
kg per m² = thickness (mm) x 7.85
kg per sq ft = kg per m² x 0.0929
sheet weight = area (m²) x kg per m²
For MS (mild steel) at 7,850 kg/m³, the figures for common thicknesses on a 2440 x 1220 mm sheet are:
| Thickness | kg/m² | kg per sq ft | 8 x 4 sheet |
|---|---|---|---|
| 0.711 mm (22 SWG) | 5.58 | 0.519 | 16.62 kg |
| 0.914 mm (20 SWG) | 7.18 | 0.667 | 21.37 kg |
| 1.219 mm (18 SWG) | 9.57 | 0.889 | 28.49 kg |
| 1.6 mm | 12.56 | 1.167 | 37.39 kg |
| 1.626 mm (16 SWG) | 12.76 | 1.185 | 37.99 kg |
Stainless 304 at 7,930 kg/m³ weighs about 1% more than MS for the same size, so an 8 x 4 sheet of 1.2 mm 304 is 28.33 kg. Aluminium is roughly a third of steel.
Which gauge? SWG against the US chart
Indian dealers and drawings often give thin sheet as a gauge: "18 gauge CRCA", "22 gauge GI". The table usually meant is the British Standard Wire Gauge, fixed in 1883 and listing each size in thousandths of an inch, as the Standard Wire Gauge history shows. Many charts on the internet are American instead, and the two only agree at some numbers:
| Gauge | SWG | US steel | 8 x 4 sheet, SWG | 8 x 4 sheet, US |
|---|---|---|---|---|
| 18 | 1.219 mm | 1.214 mm | 28.49 kg | 28.37 kg |
| 20 | 0.914 mm | 0.912 mm | 21.37 kg | 21.31 kg |
| 22 | 0.711 mm | 0.759 mm | 16.62 kg | 17.75 kg |
| 24 | 0.559 mm | 0.607 mm | 13.06 kg | 14.19 kg |
| 26 | 0.457 mm | 0.455 mm | 10.68 kg | 10.62 kg |
At 22 and 24 gauge the US chart gives about 7% and 9% more steel. If one quotation is "per sheet" and another "per kg", a wrong chart quietly changes which is cheaper. The calculator's gauge mode defaults to SWG for that reason; switch to the US table only if the supplier says so. The US galvanised column is thicker again because it includes the zinc.
GI sheet: add the zinc
The calculator weighs the steel. Galvanised (GI) sheet carries a zinc coating stated in grams per square metre (gsm). JSW Steel, for example, lists its galvanised steel to IS 277, ASTM A653 and JIS G3302, 0.13 to 3.0 mm thick and up to 2050 mm wide, with coatings up to 275 gsm.
Worked example, ten 8 x 4 GI sheets in 22 SWG with a 275 gsm coating:
steel per sheet = 2.9768 m² x 0.7112 mm x 7.85 = 16.62 kg
zinc per sheet = 2.9768 m² x 0.275 kg/m² = 0.82 kg
each = about 17.44 kg
ten sheets = 166.2 kg steel + 8.2 kg zinc = about 174.4 kg
Check the test certificate for whether the gsm figure is the total for both sides, and whether the thickness quoted is the base steel or includes the coating. On thin GI the zinc is about 5% of the weight; on 3 mm sheet it hardly registers.
More worked examples
A batch for a panel shop
Fifty CRCA sheets, 2500 x 1250 mm in 20 SWG, for control panel enclosures:
area = 3.125 m²
kg/m² = 0.9144 x 7.85 = 7.178
each = 22.43 kg
fifty = 1,121.6 kg
A little over a tonne, which matters when booking a tempo or checking the dealer's weighbridge slip.
Doors with louvre cut-outs
Forty 800 x 1800 mm panel doors in 1.6 mm CRCA, each with two 300 x 150 mm louvre openings. In the calculator, add one rectangular cut-out of 300 x 150 with a count of two:
gross area = 1.44 m²
cut-outs = 2 x 0.3 x 0.15 = 0.09 m²
net area = 1.35 m²
kg/m² = 1.6 x 7.85 = 12.56
each = 16.96 kg
forty = 678.2 kg
The doors weigh 678 kg, but the blanks you buy weigh 723 kg (1.44 m² x 12.56 x 40). Price the material on the blank and the finished weight for transport.
MS plate
At plate thickness, dealers quote in mm and gauges drop away. A 2500 x 1250 x 6 mm MS plate is 47.1 kg/m² x 3.125 m² = 147.19 kg. That is a lifting job for a chain block or forklift. For beams, channels, angles and rods, use the steel weight calculator instead.
Why the scale disagrees with the calculation
- Rolling tolerance. The mill rolls to a tolerance band, and sheet rolled to the thin side of it weighs less than the calculation. A rate per kg on theoretical weight and one on actual weight are not the same price.
- Coating. GI and colour coated sheets carry zinc and paint on top of the steel.
- Standards and marking. Adoption of Indian Standards and the ISI mark is voluntary by default, but Section 16 of the BIS Act, 2016 lets the government make it mandatory, and the Ministry of Steel lists 151 carbon, alloy and stainless steel products notified under quality control orders between 2012 and 2024. Its quality control orders page carries the current orders and exemptions. Buying certified material does not change the formula, but it does make the thickness and coating on the certificate more trustworthy inputs.
Frequently asked questions
What is the formula for MS sheet weight in kg?
Length (m) x width (m) x thickness (mm) x 7.85. For an 8 x 4 sheet (2440 x 1220 mm) in 18 SWG that is 2.9768 x 1.2192 x 7.85 = 28.49 kg. For kg per sq ft, use thickness in mm x 0.729.
How much does a 22 gauge GI sheet of 8 x 4 weigh?
About 16.62 kg of steel if the gauge is SWG (0.711 mm), plus the zinc: at 275 gsm, about 0.82 kg more. Read from a US chart (0.759 mm) the steel alone would be 17.75 kg, so ask which gauge the dealer means.
What is the weight of 1.6 mm CRCA sheet per sq ft?
1.6 x 7.85 = 12.56 kg per square metre, or about 1.167 kg per sq ft. An 8 x 4 sheet of 1.6 mm CRCA weighs 37.39 kg.
Is 16 gauge the same as 1.6 mm?
Nearly. 16 SWG is 1.626 mm, so an 8 x 4 sheet weighs 37.99 kg against 37.39 kg for 1.6 mm. The US 16 gauge is thinner at 1.519 mm. When the price is per kg, the 1.6% difference between 1.6 mm and 16 SWG is real money on a large order.
Do I weigh the finished part or the sheet?
Both, for different purposes. You pay for the full sheet or blank; transport and lifting care about the finished part. The calculator subtracts holes and cut-outs from the area to give the finished weight.
Sources and further reading
- Galvanised steel, JSW Steel. IS 277, ASTM A653 and JIS G3302; 0.13 to 3.0 mm, up to 2050 mm wide, coating up to 275 gsm.
- Standardization and quality control of iron and steel, Ministry of Steel, Government of India. 151 products notified 2012 to 2024; Section 16 of the BIS Act, 2016.
- Quality control orders, Ministry of Steel. Current steel QCOs, amendments and exemptions.
- Standard wire gauge, Wikipedia. The SWG table and its history.
- Sheet metal: gauge, Wikipedia. How the US gauge tables differ.
- Cold rolled steel, JSW Steel. CRCA coil from an Indian mill, widths up to 1870 mm.
Open the Sheet Metal Weight Calculator
More Sheet Metal & Welding
Every tool in the Sheet Metal & Welding section, free and in your browser.