PSI to Bar Converter

Convert psi to bar and bar to psi with the exact factor 1 bar = 14.5038 psi, worked arithmetic for each direction, and the common placard values explained.

The interactive tool loads here when JavaScript runs.

About this tool

What is the PSI to Bar Converter?

The sticker in a US door jamb says 32 psi; the airline at a European filling station is graduated in bar and expects something near 2.2. The two units describe the same tire, and the bridge between them is a single exact number: one bar is 14.5038 psi. Type either reading here and the other appears immediately, in both directions.

Unlike a general pressure page that spreads one value across nine units, this tool is built for the pair people actually swap between at a pump, a compressor or a dive shop. The step panel writes the division or multiplication out in full, anchored to the definitions: a bar is exactly 100,000 pascals, and a psi is exactly 6,894.757293 pascals, one avoirdupois pound-force on one square inch.

Your reading is converted on your own device and never transmitted. Each step names the exact definition it rests on, the report bar beneath the result saves the conversion as CSV or PDF, and the share link carries the figure you typed so someone else opens the identical page.

  • Two-way conversion: type in either the psi or the bar field
  • Exact factor on display: 1 bar = 100,000 Pa = 14.5038 psi
  • Worked arithmetic through pascals for every conversion
  • Presets for car placards, bicycle tires and dive cylinders
  • CSV and PDF download from the report bar, with a link that restores your input
Read the guide: Unit Conversion Factors: Exact Definitions, Gallons and Temperature Offsets

Updated

How to use the PSI to Bar Converter

  1. Type the pressure you have, in either box: psi on one side, bar on the other.
  2. The matching value appears as you type, so 32 psi immediately shows 2.206 bar.
  3. Open the calculation steps to see the arithmetic through pascals, with the exact 6,894.757293 Pa and 100,000 Pa definitions on their own lines.
  4. Use the preset buttons for door-placard, bicycle and dive-cylinder pressures.
  5. Save the result as CSV or PDF from the report bar, or copy the share link with your figure embedded.

Worked examples

US door placard at a European pump

Input

32 psi

Output

2.206 bar

32 × 6,894.757293 Pa = 220,632.23 Pa, and dividing by 100,000 Pa per bar gives 2.2063 bar. Set a pump graduated in bar to 2.2 for this placard.

European placard on a US gauge

Input

2.4 bar

Output

34.81 psi

2.4 bar is 240,000 Pa. Dividing by 6,894.757293 gives 34.809 psi, so a gauge marked only in psi should read just under 35.

Road bike tire

Input

100 psi

Output

6.895 bar

Narrow road tires run an order of magnitude above car pressures: 100 psi is 689,475.73 Pa, or 6.8948 bar. European track pumps print both scales for exactly this reason.

Espresso machine brewing pressure

Input

9 bar

Output

130.53 psi

9 × 100,000 Pa = 900,000 Pa, and dividing by 6,894.757293 gives 130.534 psi. Machines sold in the US often carry a psi gauge showing roughly 130 at the standard 9 bar setting.

Background and insight

The psi grew out of English units: force in pounds, area in square inches. Its modern value is fixed because both ingredients are. Since 1959 the pound has been 0.45359237 kg, standard gravity is 9.80665 m/s², and the inch is 25.4 mm, so one psi works out to exactly 6,894.757293168361 Pa. The bar came from the metric side, coined by the meteorologist Vilhelm Bjerknes around 1909 as a convenient round 100,000 Pa, deliberately close to average sea-level air pressure. It is not an SI unit, but it survives wherever a number near one atmosphere is handy: tires, dive cylinders, boilers, espresso machines.

That closeness to the atmosphere explains the numbers you meet. A passenger car tire at 2.2 to 2.5 bar is carrying a bit over twice atmospheric pressure above ambient; the same placard in the US reads 32 to 36 psi. A scuba cylinder filled to 3,000 psi in Florida holds 206.8 bar, while the common European fill of 232 bar is 3,365 psi. Espresso standards call for about 9 bar at the group head, which is just over 130 psi.

One habit prevents most mistakes with this pair: remember that both readings are gauge pressure, measured above the surrounding air, so they convert directly with no offset. The 14.5038 factor is all there is. The rough factor of 14.5 is fine for inflating a tire; keep the full value when the number feeds a specification or a calibration record.

Common use cases

  • Rental cars and imports

    Match a psi door placard to a bar-only airline abroad, or a bar placard to a US gauge at home.

  • Cycling

    Translate the psi range molded on a tire sidewall for a floor pump whose dial reads bar.

  • Diving

    Compare cylinder fills and gauge readings between psi and bar regions before a trip or an equipment purchase.

  • Workshop equipment

    Set a compressor, regulator or spray gun whose manual quotes one unit while the dial shows the other.

Tips and limitations

  • Divide psi by 14.5 for a quick bar estimate; the exact divisor is 14.5038, and the difference only matters past the second decimal.
  • Inflate tires cold. Driving warms the air and raises the reading by a few psi (a few tenths of a bar), which is normal and not a reason to bleed pressure.
  • A 0.1 bar step is about 1.45 psi, so a bar gauge with 0.1 graduations resolves tire pressure about as finely as a psi gauge with whole-number marks.
  • Some European pumps read kPa instead: multiply bar by 100, so 2.3 bar is 230 kPa.
  • Both units here are gauge pressure, measured above atmospheric. Converting the number never changes the reference point, so psi converts to bar with no offset.

Sources and further reading

  1. NIST Special Publication 811: Guide for the Use of the International System of Units, NIST. The exact pascal value of the psi in Appendix B
  2. Bar (unit), Wikipedia. Origin of the bar and its 100,000 Pa definition
  3. The International System of Units (SI Brochure), BIPM. Status of the bar among non-SI units

Frequently asked questions

How many psi is 1 bar?

14.5038 psi, from 100,000 Pa divided by the exact psi definition of 6,894.757293 Pa. Going the other way, 1 psi is 0.06895 bar.

What is 2.4 bar in psi?

34.81 psi. Multiply 2.4 by 100,000 to get pascals, then divide by 6,894.757293. The rough rule of 14.5 psi per bar gives 34.8, the same answer at tire-gauge precision.

Is 36 psi the same as 2.5 bar?

Nearly, but not exactly: 36 psi is 2.482 bar, and 2.5 bar is 36.26 psi. For inflating a tire the quarter-psi gap is irrelevant; for documenting a test pressure, state which figure you actually set.

Why do European pumps show bar instead of psi?

Europe adopted metric pressure units, and the bar earned its place as a convenient 100,000 Pa that sits close to one atmosphere, so everyday tire values land in a tidy 2 to 3 range. The psi survives in North America and on equipment built to US specifications.

Can I just multiply psi by 0.07 to get bar?

As a mental shortcut, yes: the true factor is 0.068948, so multiplying by 0.07 overshoots by about 1.5%. On a 32 psi placard that is 2.24 instead of 2.21 bar, close enough for air but not for a calibration sheet.

What pressure does a scuba tank hold in bar?

A common US aluminum cylinder rated 3,000 psi holds 206.8 bar. European cylinders are typically rated 200, 232 or 300 bar, which read 2,901, 3,365 and 4,351 psi on a US gauge.

Is there an in-depth guide to the PSI to Bar Converter?

Yes. “Unit Conversion Factors: Exact Definitions, Gallons and Temperature Offsets” covers the background, how it works, common pitfalls and worked examples. Read the full guide.