Acceleration Converter

Convert acceleration between m/s², standard gravity, ft/s², km/h/s and Gal. Turn a 0-60 time into g and see the exact constant behind every factor.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Acceleration Converter?

Enter an acceleration once and see it in metres per second squared, multiples of standard gravity, feet per second squared, kilometres per hour per second and Gal, all at the same time. Choose a target unit and the steps for that pair are written out with the constant used, so 4.4704 m/s² is shown dividing by 9.80665 to give 0.456 g₀.

The anchor for most of these units is standard gravity, g₀ = 9.80665 m/s² exactly, the conventional value fixed by the CGPM in 1901. Car magazines quote 0-60 mph times, flight tests and roller coasters quote g, geophysicists quote milligals, and lab work uses plain m/s². This converter puts them on one line so a 6-second 0-60 run reads directly as 0.46 g of average acceleration.

It all runs locally in your browser with nothing transmitted, the working names the exact constant for each step, and the report bar under the tool exports the conversion table as CSV or PDF and gives you a link that restores the same input.

  • Single input converted to m/s², g₀, ft/s², km/h/s and Gal together
  • Step-by-step working for any target, naming the exact constant used
  • Standard gravity at its defined value, 9.80665 m/s²
  • CSV and PDF export from the report bar below the tool
  • Runs in the browser with a shareable link; nothing is uploaded
Read the guide: Unit Conversion Factors: Exact Definitions, Gallons and Temperature Offsets

Updated

How to use the Acceleration Converter

  1. Type the acceleration value you have.
  2. Select its unit: m/s², g₀, ft/s², km/h/s or Gal.
  3. Read the equivalents in every other unit in the results table.
  4. Pick a target unit to see the arithmetic with the exact constant, for example the 9.80665 m/s² definition of g₀.
  5. Download the table as CSV or PDF from the report bar, or share the link.

Worked examples

A 0-60 mph time as g-force

Input

4.4704 m/s² (60 mph in 6.0 s)

Output

0.456 g₀ = 14.67 ft/s²

60 mph is 26.8224 m/s, so a 6-second run averages 26.8224 ÷ 6 = 4.4704 m/s². Dividing by 9.80665 expresses it as 0.456 g, less than half the acceleration of free fall.

One g in every unit

Input

1 g₀

Output

9.80665 m/s² = 32.174 ft/s² = 35.304 km/h/s = 980.665 Gal

Standard gravity is exact by definition, so these are the fixed anchors: multiply by 3.6 for km/h/s, divide by 0.3048 for ft/s², multiply by 100 for Gal.

Roller coaster peak

Input

3 g₀

Output

29.42 m/s² = 96.52 ft/s²

3 × 9.80665 = 29.42 m/s². At the bottom of a loop the seat pushes up with three times the rider's weight; the figure is momentary, which is why it is tolerable.

Automotive unit to SI

Input

10 km/h/s

Output

2.778 m/s² = 0.283 g₀

10 ÷ 3.6 = 2.778 m/s², then dividing by 9.80665 gives 0.283 g. Gaining 10 km/h every second is brisk but ordinary acceleration for a passenger car.

Background and insight

Acceleration is the rate of change of velocity, so its units are always a speed per unit time. The SI unit is the metre per second squared. The automotive unit km/h/s is the most intuitive of the set: a car gaining 10 km/h of speed every second is accelerating at 10 km/h/s, which is 2.78 m/s² or 0.28 g. A 0-60 mph time converts the same way: 60 mph is 26.8224 m/s, so a 6.0-second run averages 4.4704 m/s².

Expressing acceleration in g makes it directly comparable to what a body feels. Standard gravity, 9.80665 m/s², is a convention rather than a measurement; real gravity varies from about 9.78 m/s² at the equator to about 9.83 m/s² at the poles. A rider pulling 3 g at the bottom of a coaster loop experiences a support force of three times body weight, about 29.42 m/s² of acceleration. Sustained g matters very differently from momentary g, which is why ride and aviation figures always state a duration alongside the peak.

The Gal, named after Galileo, is the CGS unit: 1 cm/s², so g₀ is 980.665 Gal. It survives in gravimetry and geodesy, where surveys map variations in Earth's gravity field in milligals, a convenient size because the whole equator-to-pole variation is only about 5,000 mGal. The foot per second squared remains standard in US aerospace work; 1 g is 32.174 ft/s², a constant worth recognising on sight in older flight-test literature.

Common use cases

  • Car performance figures

    Turn 0-60 and 0-100 km/h times into average g and m/s² to compare across road tests.

  • Ride and amusement engineering

    Express coaster and drop-tower peaks quoted in g as m/s² or ft/s² for structural calculations.

  • Vibration and shock testing

    Convert accelerometer specs and test levels between g and m/s² when standards mix the two.

  • Gravimetry and geophysics

    Move between m/s² and Gal or milligal when reading gravity survey data.

Tips and limitations

  • g₀ is a defined constant, 9.80665 m/s² exactly; your local gravity differs from it by up to about half a percent.
  • A 0-60 mph calculation gives average acceleration; the instantaneous peak in first gear is higher.
  • Accelerometer datasheets usually quote g; multiply by 9.80665 before using the value in SI formulas.
  • km/h/s and m/s² differ only by the factor 3.6, the same one that links km/h and m/s.
  • In gravity surveys 1 mGal is 10⁻⁵ m/s², roughly the change from climbing three metres in elevation.

Sources and further reading

  1. The International System of Units (SI Brochure), BIPM. The m/s² as the coherent SI unit and non-SI units accepted for use
  2. Standard gravity, Wikipedia. The 1901 CGPM resolution defining 9.80665 m/s²
  3. NIST Special Publication 811: Guide for the Use of the International System of Units, NIST. Conversion factors for ft/s², Gal and gravitational units

Frequently asked questions

What is 1 g in m/s² and ft/s²?

Standard gravity is 9.80665 m/s² exactly, which is 32.174 ft/s² and 35.304 km/h/s. The value is a convention adopted by the CGPM in 1901, not a measurement of any particular place.

How do I turn a 0-60 time into g?

Convert 60 mph to 26.8224 m/s, divide by the time in seconds to get m/s², then divide by 9.80665. A 6.0-second car averages 0.456 g; a 3.0-second car averages 0.91 g.

Is g the same everywhere on Earth?

No. Measured gravity runs from about 9.78 m/s² at the equator to about 9.83 m/s² at the poles because of Earth's rotation and shape. The symbol g₀ refers to the fixed conventional value, 9.80665 m/s², which this converter uses.

What is a Gal?

The Gal, named after Galileo, is the CGS acceleration unit, 1 cm/s². Gravimetry uses the milligal, 10⁻⁵ m/s², to map tiny variations in Earth's gravity field; standard gravity is 980.665 Gal.

How many g do roller coasters reach?

Momentary peaks of several g occur at the bottoms of loops and valleys; 3 g corresponds to 29.42 m/s² and a seat force of three times body weight. The duration matters as much as the peak, which is why rides sustain high g only for moments.

What does km/h/s mean?

Kilometres per hour gained per second, the natural unit for reading a speedometer: 10 km/h/s means the needle climbs 10 km/h each second. Divide by 3.6 to get m/s².

Is there an in-depth guide to the Acceleration Converter?

Yes. “Unit Conversion Factors: Exact Definitions, Gallons and Temperature Offsets” covers the background, how it works, common pitfalls and worked examples. Read the full guide.